Amplifier Research 100S1G6 Solid State Amplifier 0.7GHz – 6GHz 100W

Description

Amplifier Research 100S1G6 is a solid-state; Class A design, self-contained, air-cooled, broadband amplifier designed for applications where instantaneous bandwidth, high gain and linearity are required. Housed in a stylish contemporary cabinet, the unit is designed for benchtop use, but can be removed from the cabinet for immediate equipment rack mounting.

The 100S1G6, when used with a sweep generator, will provide a minimum of 100 watts of RF power. Included is a front panel gain control which permits the operator to conveniently set the desired output level.

The 100S1G6 is protected from RF input overdrive by an RF input leveling circuit which controls the RF input level to the RF amplifier first stage when the RF input level is increased above 0 dBm. The RF amplifier stages are protected from over-temperature by removing the DC voltage to them if an over-temperature condition occurs due to cooling blockage or fan failure. There is a digital display on the front panel to indicate the operate status and fault conditions if an over-temperature or power supply fault has occurred. The unit can be returned to operate when the condition has been cleared.

All amplifier control functions and status indications are available remotely in GPIB/IEEE-488 format, RS-232 hardwire and fiber optic, USB, and Ethernet. The bus interface connector is located on the back panel and positive control of local or remote operation is assured by a Local/Remote switch on the front panel of the amplifier.

The low level of spurious signals and linearity of the Model 100S1G6 make it ideal for use as a driver amplifier in testing wireless and communication components and subsystems. It can be used as a test instrument covering multiple frequency bands and is suitable for a variety of communication technologies such as CDMA, WCDMA, TDMA, GSM etc. It is also suitable for EMC Test applications where undistorted modulation envelopes are desired.

 

Features

  • Solid State Broadband
  • Mismatch Tolerant
  • Modulation Capability
  • Digital Control Panel
  • Automatic Primary Power Selection
  • RF Input Leveling Circuit – Overdrive Protection
  • Over Temperature Protection
  • Standard Remote Interfaces
Download Data Sheet
Print
Email

Specifications

RATED POWER OUTPUT

100 watts minimum (0.7-6.0 GHz)

INPUT FOR RATED OUTPUT

1.0 milliwatt maximum

POWER OUTPUT @ 3dB COMPRESSION

Nominal

120 watts

Minimum

100 watts

POWER OUTPUT @ 1dB COMPRESSION

Nominal

100 watts

Minimum

80 watts

FLATNESS

±1.5 dB typical

±2.5 dB maximum

FREQUENCY RESPONSE

0.7-6.0 GHz instantaneously

GAIN (at maximum setting)

52 dB minimum

GAIN ADJUSTMENT (Continuous Range)

10 dB minimum (4096 steps remote)

INPUT IMPEDANCE

50 ohms, VSWR 2.0:1 maximum

OUTPUT IMPEDANCE

50 ohms, nominal

MISMATCH TOLERANCE

100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance.

MODULATION CAPABILITY

Will faithfully reproduce AM, FM, or pulse modulation appearing on the input signal

HARMONIC DISTORTION

Minus 20 dBc maximum at 80 watts (1.0-6.0 GHz)

Minus 15 dBc typical at 80 watts (0.7-1.0 GHz)

THIRD ORDER INTERCEPT POINT

58 dBm typical

NOISE FIGURE

10 dB typical

SPURIOUS

Minus 73 dBc typical

PHASE LINEARITY

+1.0 deg/100 MHz, typical

PRIMARY POWER

(selected automatically)

90-132, 180-264 VAC

50/60 Hz, single phase

1100 watts maximum

CONNECTORS

RF INPUT & OUTPUT

Type N female on front panel

REMOTE INTERFACES

IEEE-488

24 pin female

RS-232

9 pin Subminiature D (female)

RS-232 (Fiber-optic)

Type ST

USB 2.0

Type B

Ethernet

RJ-45

SAFETY INTERLOCK

15 Pin Subminiature D

COOLING

Forced air (self contained fans)

SIZE (W x H x D)

50.3 x 30 x 61cm, 19.8 x 11.8 x 24 in

WEIGHT (approximate)

45 kg (100 lbs)

Stay informed

To keep you in the loop of our latest news, register now for our email newsletter.